Car keys · Woolwich
Ignition Lock Repair
The key turned the engine off in the driveway and now refuses to come back out.
In plain words
The visit follows a steady order. On the phone, the vehicle and the exact symptom are described so the right parts and tools come along for the trip. On arrival, ownership is confirmed, the mechanism is assessed, and the cylinder is serviced, repinned or replaced as the fault requires. Every switch position is tested afterward, along with the steering lock, before the visit is called finished and any remaining electronic question is named separately.
How the visit goesThe car arrived with one worn-looking key and a story about a lost spare. It turns the ignition, eventually, after some patience and a particular angle nobody in the household can quite describe or repeat on the first try.
Ignition Lock Repair
How the visit goes
What the vehicle's build decides about access
Every vehicle's ignition assembly is put together a little differently: many use a steering-column cylinder in a simple housing or one locked down with shear bolts, while others mount the keyed switch in the instrument panel behind its own trim that has to come off cleanly to avoid marking the dash. The locksmith identifies which arrangement is in front of them before starting, since that decides which tools come out of the case and how the surrounding trim gets handled once the cylinder itself is reached.
Working around the steering column carefully
Reaching some ignition cylinders means removing steering column trim and shrouding first, and that work is done with the fasteners and clips the vehicle was built with rather than force. Wiring and components near the column, including anything related to the airbag system, are left exactly as found and never disturbed unnecessarily. Once the cylinder is serviced or replaced, every panel and clip goes back the way it came off, so nothing rattles or sits loose afterward.
A cylinder and key with a clean history behind them
Where the ignition showed signs of an earlier forced attempt, the replacement hardware carries none of that history forward: new pins, a new key, and a housing that has not been tampered with. You are shown the old part before it is handed over or taken away, so the vehicle's ignition starts its next chapter with hardware nobody has already tried once to defeat.
Ignition Lock Repair
In the van
Key blanks and cutting machine
Ignition lock cylinder
Keyed-alike pinning kit
Trim clips and fasteners
Key code reader
Ignition Lock Repair
What affects the quote
Weather and road conditions on the day
A barrel packed with road salt, grit or old grease from a rough season takes longer to clean and free than one that has simply worn with ordinary use over the years of driving.
Evidence of an earlier forced attempt
A lock that shows signs of having already been forced needs a full cylinder and housing replacement rather than a simple service, since the internal parts can no longer be trusted as they stand.
Access through the steering column
Reaching some ignition cylinders means removing trim, shrouding or fasteners around the column first, and putting all of it back cleanly afterward. A column that is straightforward to open takes less time than one that is not.
What to have ready
- Are any warning or immobilizer lights showing on the dash?
- Does the key insert, turn partway, or not turn at all?
- Do the doors or trunk use the same key as the ignition?
Ignition Lock Repair: questions
QuestionsDo you need to confirm that I own the vehicle before starting?
Yes, and it takes only a moment when the paperwork is on hand. A vehicle permit or registration document matched to identification settles it in most cases. If the vehicle is a rental, a fleet vehicle or belongs to someone else, a lease, a work order or a call to the registered owner fills the gap. This step protects every vehicle owner who might one day call about their own ignition.
What if the key won't go into the slot at all?
That points toward the barrel itself, debris packed into the keyway, or a key that has bent or worn out of shape rather than a deeper electronic problem. The keyway is checked and cleared first, the key is compared against a spare if one exists, and the barrel is serviced or replaced depending on what that first check turns up.
I just bought a used vehicle with one worn key. What should I expect?
A single worn key is a common starting point after buying used, and the visit usually has two parts: reading the existing wafers so a crisp new key can be cut, and deciding whether the barrel itself needs a service given whatever wear the previous owner's key left behind. Bringing whatever paperwork came with the sale helps confirm ownership before any work begins.
Related services
- Car Key ReplacementYou bought the car privately and it came with a single key on a shoelace.
- Spare Car Key DuplicationThe proximity fob has ridden in a pocket for years, the range feels shorter than it used to, and a dashboard warning mentioned a battery a while back.
- Key Fob ProgrammingA fob went missing weeks ago somewhere between a coat pocket and a parking lot, and a spare has covered the gap since.